Shrubs for Shade

How can I propagate Aucuba japonica?

Propagate Aucuba japonica from semi-ripe or spring cuttings, layering or seed. Step-by-step methods, timings and why cuttings keep the parent's sex.

On this page
  1. The short answer
  2. Propagation methods compared
  3. Taking semi-ripe cuttings (step by step)
  4. Spring softwood cuttings
  5. Can you root aucuba in water?
  6. Layering
  7. Growing aucuba from seed
  8. Male or female? Why the method matters
  9. Aftercare and potting on
  10. Troubleshooting cuttings

The short answer

The easiest way to propagate Aucuba japonica is from semi-ripe cuttings taken in late summer, roughly July to September. Cut 10–15cm shoot tips, remove the lower leaves, insert them into pots of free-draining compost, cover them to keep the air humid, and keep them somewhere cool and shaded. Aucuba roots readily, often without rooting hormone.

You can also root softwood cuttings in spring, layer low branches into the soil, or grow aucuba from seed. Cuttings and layers keep the sex and leaf pattern of the parent, which matters if you want berries.

Propagation methods compared

Method When Ease Result
Semi-ripe cuttings Late summer Easy Identical to parent, same sex
Softwood cuttings Spring to early summer Fairly easy, wilt-prone Identical to parent, same sex
Water rooting Spring or summer Easy but weaker roots Identical to parent, same sex
Layering Spring or autumn Very easy, slow Identical to parent, same sex
Seed Sow fresh, from ripe berries Slow and unpredictable Variable, sex unknown

Taking semi-ripe cuttings (step by step)

Semi-ripe cuttings come from this year’s growth that has started to firm up at the base but is still flexible at the tip.

  1. Take cuttings in the morning, when the plant is full of water. Choose healthy, non-flowering shoots and cut 10–15cm tips with a sharp knife or clean secateurs, just below a leaf joint.
  2. Keep them moist. Put them straight into a plastic bag. If you can’t prepare them right away, keep the bag somewhere cool, such as the fridge, for a short time.
  3. Strip the lower leaves from the bottom half of each cutting. Aucuba leaves are large, so cut the remaining leaves in half across their width. This reduces water loss while roots form.
  4. Dip in rooting hormone if you like. Aucuba often roots well without it, but hormone may speed things up.
  5. Insert into compost. Use small pots of free-draining mix, for example roughly equal parts peat-free multipurpose compost and grit, perlite or sharp sand. Push the cuttings in so the bottom half is buried and the leaves don’t touch the compost. Several cuttings can share a pot around the edge.
  6. Water and cover. Water well, let the pots drain, then cover them with a clear plastic bag held off the leaves with sticks, or place them in a propagator or cold frame.
  7. Keep them out of direct sun, in a cool, bright spot. Check every week or so, remove any fallen or rotting leaves, and mist lightly if the leaves look limp.

Roots usually form within a few weeks to a couple of months. A gentle tug that meets resistance, or roots showing at the drainage holes, means the cutting has rooted.

Spring softwood cuttings

You can also take soft, fast-growing shoot tips in spring or early summer. They usually root a little faster than semi-ripe cuttings but wilt more easily, so humidity is more important. Use the same method, keep them covered, and keep them out of direct sun.

Can you root aucuba in water?

Yes. Aucuba will often root in a jar of water, and it can be a fun experiment. However, roots formed in water tend to be thinner and weaker than those formed in compost, and cuttings can struggle when moved into soil.

If you try it:

  • remove all leaves that would sit below the waterline
  • change the water every few days
  • pot the cutting into compost once roots are about 2–3cm long, and keep it humid for a week or two while it adjusts

For stronger plants, rooting in compost is usually more reliable.

Layering

Layering is the most foolproof method, and it suits established shrubs with low, flexible branches.

  1. In spring or autumn, choose a low branch that will bend down to the soil.
  2. Where it meets the ground, make a small slanting cut partway through the underside of the stem, or scrape off a short strip of bark.
  3. Bury that section of stem a few centimetres deep in loosened soil, peg it down with a bent wire or a stone, and tie the tip upright to a cane.
  4. Keep the area moist.

Roots usually form over the following months. Once the layer has a good root system, often after about a year, cut it from the parent plant and move it to its new position or a pot.

Growing aucuba from seed

Seed is the slowest and least predictable method, but it’s an interesting project.

  • Pick ripe red berries from a female plant that has been pollinated by a nearby male.
  • Remove the fleshy pulp, then sow the seeds fresh in pots or trays of peat-free seed compost, covering them lightly.
  • Keep them in a cold frame, unheated greenhouse or sheltered spot outdoors.

Germination is often slow and irregular. The RHS notes it can take up to 18 months. Seedlings won’t necessarily resemble the parent, variegated plants may produce plain green offspring, and you won’t know whether a seedling is male or female until it flowers, which can take several years.

Male or female? Why the method matters

Aucuba plants are usually either male or female, and only females produce berries. Cuttings and layers are clones of the parent:

  • cuttings from a female give female plants that berry if a male is nearby
  • cuttings from a male give male plants that can pollinate your females
  • cuttings from a self-fertile cultivar such as ‘Rozannie’ should berry on their own

If you want a reliable berry display, take cuttings from both a female and a male. See our Aucuba japonica growing guide for a table of male, female and compact varieties.

Aftercare and potting on

  • Uncover gradually once the cuttings have rooted, opening the bag or propagator a little more each day.
  • Overwinter late-summer cuttings in a cold frame, cool greenhouse or sheltered spot, keeping the compost just moist.
  • Pot on in spring into individual pots of multipurpose or soil-based compost.
  • Grow on for a year or so in a shady or partly shady spot before planting out, or move them into a larger container. Our guide to hardy evergreen shrubs for pots in shade covers long-term container care.

Troubleshooting cuttings

  • Cuttings wilting: not enough humidity, too much sun or leaves too large. Keep them covered, shade them and halve the leaves.
  • Cuttings rotting at the base: compost too wet or poorly drained. Use more grit or perlite and water less.
  • Blackened leaves: often too wet or too cold. Remove affected leaves and improve ventilation slightly.
  • No roots after many weeks: semi-ripe cuttings can be slow. If the stem is still green and firm, leave it. Many will root by spring.

Aucuba is one of the best shrubs for shade, so it’s well worth multiplying. For other shade-tolerant shrubs to grow alongside it, see our main guide to shrubs for shade.

The complete guide to shrubs for shade

Shrubs for Shade: Evergreen and Native Choices
Read the guide

Keep exploring

Guides from other topics

All topics →